Home > Dvd Drive > Can You Connect A Dvd Drive And One Hard Drive On One Ribbon Cable?

Can You Connect A Dvd Drive And One Hard Drive On One Ribbon Cable?

Contents

Reply aDarkness January 8, 2016 at 12:30 pm Search for a SATA Data Transfer Y-Cable. I did everything is great on the old good HD, but i can't access the failing HD. ukb0082nd July 2010, 15:16Hi, PROs. There is no software. This Site

If your optical drive uses plain ATA 33 to work, it's not recommended to combine it with a hard drive, because the speed of the hard drive may be lower, you If you want to use the cable select with the older drive on a 40-wire cable, you'll have to consult the maker of the drive for the instructions. Reply bill December 23, 2014 at 9:09 pm if there is not a 2nd plugin can a splitter be used for power source? What is the software to make the drive be recognized.

How To Connect Ide Dvd Drive To Sata Motherboard

Subscribe to Our Newsletter Email: Advertisement Scroll down for the next article © 2017 MakeUseOf. This stripe tells you that the wire on that side is attached to Pin 1 of each connector. For our purposes, touching a radiator will suffice. This position is used to ensure that the cable is attached to the drive in the correct position.

  1. Take a look at one of your other devices to work out which the power cables are in your case. The IDE connector is also easy, the same as the motherboard it
  2. In short - you CAN make a CD-ROM and a HDD share an IDE channel, but it will usually impact HDD performance.
  3. This is nevertheless a very useful guide and very clear so thank you for it(I have bought several drives and they haven't had screws again check ebay or your local repair

Connect the drive using the Master connector on the secondary IDE cable. Anmelden Teilen Mehr Melden Möchtest du dieses Video melden? If it doesn't work, your drive is dead, or not powered correctly. How To Install A Second Dvd Drive To reduce the chance of ESD damage, work over a noncarpeted floor, use a static dissipative work surface (such as a conductive foam pad), and wear an ESD wrist strap connected

IDE ribbon cables have either 40 or 80 wires. How To Connect Cd Drive To Pc Most ribbon cables have 2 attachments - your main drive should be attached to the master attachment. Each device must also be set with a hardware switch (a jumper) as to whether it is supposed to be the master or the slave. Some hard drives can take either kind of cable, but the SATA type are easier to plug in so I use those if available.

the Global Study Desk nadun flower Reply Priyankar November 22, 2016 at 4:07 am I did the same procedure, what you have written but can't find the 2hdd option in" my Sata Dvd Drive Set the first CD/DVD drive jumper to Master (alternatively, Cable Select can be used if you set the second CD/DVD drive selection to Cable Select). How much degradation you experience depends on the patterns of your disk use and which IDE standards are involved. (I exclude these complexities here.) For typical office work this configuration works Be extra special careful about your Master / Slave jumper settings.

How To Connect Cd Drive To Pc

PDA View Full Version : Can dvdRW and HDD share same data cable? All trademarks, icons, and logos shown or mentioned in this web site are the property of their respective owners. How To Connect Ide Dvd Drive To Sata Motherboard Gosh, it's been awhile since I've thought about that stuff!! How To Connect Dvd Drive To Motherboard Sata Reply cezar August 6, 2016 at 9:56 pm I have an old sata HD that came with the PC but the capacity was way to small, so i put in my

Burn this in to your brain kids. Clicking Here Had to buy a "new" hard drive from Hunter Engineering, and Frankenstein some old parts together. The hard drive is a fairly sizeable chunk of metal like this: You should find it sitting in a metal cage of some sort. However, one of the gaps between the end connectors and the middle connector is longer – this is the end that plugs into your motherboard. Ide Hard Drive Jumper Settings

This is normally where you connect your lesser used devices like CDROMs, CDROM Burners and Tape Drives. This chart summarizes the three drive integration solutions I've described: USB Toolset: Drive Dongle: Controller Card: Mounts Drive(s): External Internal Internal & External * Requires Software Driver: No No Yes Supports ASSIGN THE FOLLOWING DRIVE LETTER > next 6. read review Wird geladen...

Both drives on a channel must support CSEL, both drives must be jumpered as CSEL, a CSEL cable must be used, and the host interface connector must support CSEL. Ide To Sata Converter Hard disks have passed through a long evolution of connectivity and data transfer standards. This picture shows the pieces in  Eforcity's PATA and SATA Converter Set: Eforcity's USB Connector Set (Eforcity and Amazon) You use your computers' USB port as the interface to connect your

IDE includes sub-standards with names like EIDE, ATAPI, ATA, ATA-1, ATA-2, UDMA, ATA-4, ATA-133, and more.

Here's how the IDE connector sockets on the motherboard look, along with the ribbon cable that goes from the motherboard socket into the back of any IDE drive: PATA Photos (Wikipedia If you're adding a second IDE drive, set its jumper to Slave.If you're installing a SATA drive, jump to the following step. 5Attach rails to your DVD drive, if your case Forum Rules | Contact Forum Editor | Report a Post Pages 1 2 >> Next… CD Rom and HDD on same IDE cable? Sata To Ide Adapter Check now to see if you have room to fit another one in there.

PIO 4 is the worst, ATA 33 is better, ATA 66, 100 and 133 are the best but require an IDE cable that has 80 wires instead of 40 wires. Ballie 18:57 20 Dec 09 xania,thanks for the link I have now ordered one, seems the best way to connect it to one of the SATA plugs. Drive dongles like the Syba do not require device drivers. try here Write out a quick table to figure out how it is currently set up, like this: CHANNEL 1, MASTER: CHANNEL 1, SLAVE: CHANNEL 2, MASTER: CHANNEL 2, SLAVE: Probably your hard

next 8. (when finished) > finish *** now your hdd will show up in windows explorer (or my computer) because NOW ONLY it (JUST) became usable! Reply Charlsu August 29, 2016 at 2:39 pm I only have one sata port on my board can i still add one more drive? You can get an ATX to SATA power adaptor very cheap. I wouldn't.

All Rights Reserved Tom's Hardware Guide ™ Ad choices PC Advisor Phones Smartphone reviews Best smartphones Smartphone tips Smartphone buying advice Smartphone deals Laptops Laptops reviews Laptops tips Best laptops Laptops The slave goes in the middle connector.