Home > Graphics Card > Cant Get New Video Card To Work

Cant Get New Video Card To Work


The steps above make the integrated video completely vanish from the computer. Just remember to re-enable it once you've got your new video card up and running. You'll have to take a careful look and see what kind of retention mechanism you have and get it prepared if necessary. You can tell that it's all the way in by seeing that the "golden fingers" on the circuit board are all the way into the expansion slot. check that

You may have to tell the BIOS which video card is your primary video display. There are usually four or more of those screws holding down the motherboard. Once it's unlatched you're ready to remove the video card. You can reuse the same screw(s) that held the cover bracket or your former graphics card in place.

No Display From Graphics Card

I say "usually" because sometimes it won't allow it. But DVI can get a bit complicated because different DVI outputs can have different capabilities. One monitor is your primary display. If your machine can't disable the integrated video then you may be able to just disable the display driver.

Install the display drivers for your new video card. The motherboard and video card documentation will explain how to do it. But, what PSU (Power Supply) are you using. Open your case to get access to the expansion slots Case designers seem to be thinking one of two things when designing a case: "allow these clever computer users to have

You just disabled your integrated video in the BIOS. As about beeps, I don't hear a beep at all. Hovsep A March 20, 2014 at 4:04 pm is it possible for you to check the BIOS and disable the on board graphic card, normally it should be done automatically...maybe it It's also the main monitor in Windows where the taskbar and icons appear.

If you can't find the documentation then check the manufacturer's website for your computer model. I ran to bestbuy about an hr ago and that was the problem then returned it lol. Open your case to get access to the expansion slots. Some newer computers allow you to hook one monitor to your integrated video and another monitor to an AGP or PCI-Express x16 video card.

Graphics Card Not Working

It may show you the arcane series of steps needed to get it to work. But are your frame rates anything like these... No Display From Graphics Card Most cases hold the video card into the case with a single screw. How To Install A New Graphics Card mxdirector Dec 29, 2015 10:56 AM (in response to mxdirector) Yes I have tried installing new graphics drivers, tried updating them through the device manager and then downloaded the latest from

But it also contains some chips which make all those parts work together. http://magicnewspaper.com/graphics-card/solved-just-got-a-new-video-card-and-cant-get-it-to-work.html You can usually fiddle around inside a computer with only the standby power running but it's not a good idea. If you're not sure which one to use then just use DVI. Some video cards use too much power to get it from the expansion slot so they need an auxiliary power cable.

The best drivers to use are ones which you download from the GPU maker (usually ATI or NVIDIA). I can only compair to my desktop as my Thinkpad only has the i7 as a GPU. But an ATX computer isn't really fully off. Go Here You can cause some very subtle problems by installing new drivers over older ones because vestiges of the old driver may still be hanging around in your system.

Some video card slots don't have a retention mechanism. The ground wire is connected to the metal case of your power supply and to the metal parts of the computer case. The manual for your computer should explain how to clear the CMOS RAM.

They're already installed but are disabled.

Thomas RyanIf your new graphics card is the same brand as your old card, this process is simple. or at least the symptoms you're describing are 100% as mine. The common lever type shown in this image should latch automatically when the card is pressed fully into the slot. Don't remove them unless you'd like to have your power supply rattling around inside your case.

The thing is, a BIOS upgrade should not kill the onboard graphics port. Discussion topics include choosing a processor, installing hard drives, adding RAM, upgrading video cards, sound cards, DVD drives, Blu-ray drives, PSU, and much more.Real-Time ActivityMy Tracked DiscussionsFAQsPoliciesModerators General discussion Can't get It looks a little silly but accomplishes the same thing. More hints Install the display drivers for your new video card.

now the problem is definitely narrowed down to the motherboard. The steps in each list must be done in order. Compaq was especially notorious for shipping that kind of computer. You can tell if your machine can disable the integrated video by looking for that option in the BIOS.

You have to push the lever towards the motherboard to unlatch the card. Show More Few upgrades add as much punch to your PC as tomtalk24 Dec 28, 2015 1:22 PM (in response to mxdirector) You just want to get on and use your Laptop so.... After the installation is finished you reboot your machine and you're done.

If you're installing two video cards (for SLI or CrossFire ) then you'll probably have to move some small circuit boards or jumpers around on the motherboard before installing the video As a rule of thumb, your power supply should be rated from double the power consumption of your graphics card. Osama J March 22, 2014 at 5:37 am But the intel sandy bridge series is compatible with that card. Some BIOSes have a confusing choice called "Auto".

This is a good example of the hard-to-open school of thought. Like Show 1 Likes(1) Actions Re: can't get graphics card to work. I tried a lot but was unable to get anything up on monitor. Only administrators are allowed to install and uninstall drivers and most other software.

Video card installations usually go off without a hitch. That kind of motherboard always uses the integrated video as its primary video display. So I claimed the warranty and they just replaced the card with a new one. I dont know Laptops very well, but you should have an option in Crimson to tell what games use what GPU.

If your house was wired properly then touching ground is perfectly safe. Some retention mechanisms will click shut when the card is pushed all the way in. But if you're not sure about your wiring (or you're just paranoid) then unplugging the power cord will keep you from getting any jolts. I forget to connect them all the time.