Home > Hard Disk > IDE Devices Not Working

IDE Devices Not Working


The drive was showing up there and when I right clicked and choose Explore it popped up in My Computer and seems to be working fine. Some removable media devices, such as a ZIP drive, might require only a driver installation in Windows to make it usable. The followed screen looks like this. After the drive is configured, it's time to make sure the same is true of the media it uses.

It is not detecting anything IDE. But if all of your IDE is bad, then your motherboard is likely bad. The ribbon data cable should have 80 wires in it, even though the connectors only have 40 holes in them. You can also partition some large (1GB and larger) removable-media drives, but optical drives and small removable-media drives don't require partitioning.

Detecting Ide Drives Problem

BUY NOW FREE TRIAL Data Recovery Wizard for Mac Best Mac data recovery software recovers whatever you lost from Mac machines & storage devices. Most modern CD drives are ATA33 while the modern hard drives are ATA133. But, entry is usually provided by pressing the DEL key, the F2 key, the F11 key or the F12 key during POST. 0Votes Share Flag Back to Hardware Forum 9 total Reply 0 0 1167Abigail Honor Student Posts: 2 Member Since: ‎01-13-2017 Message 10 of 11 (203 Views) Report Inappropriate Content Re: no ide device detected Options Mark as New Bookmark Subscribe

You may also... POWER CABLES AND THEN DO THIS....DVD-R SET AS A MASTER...YOU KNOW HOW TO DO THAT...OKTHEN SET THE OTHER CD DRIVE AS A SLAVETHEN SET YOUR HHD DRIVE AS A CS CABLE both of them are set to cable select, because whenever I change settings like set HDD to Master my PC wont boot at all and displays "MAC ADDRESS 00-XXXX-XXXX" x's are How To Repair Hard Disk Not Detected The install disk comes on a floppy so if you don't have one then you'd better be able to do a BIOS update.

OK HERE IS A LITLE BIT HARDER TO SAY BUT I AM PRETTY SURE WHAT IS...TRY THIS ONE MAKE SURE CABLES ARE SECURELY CONNECTED THEN MAKE SURE ARE PIN 1RED DOT All Rights Reserved Tom's Hardware Guide ™ Ad choices Login _ Social Sharing Find TechSpot on... So the device manager entry is correct. What are the messages?

Aug 2, 2010 #11 raybay TS Evangelist Posts: 7,241 +9 Nearly all of such issues are caused by setup errors in the BIOS... Internal Hard Disk Not Detected Initialize the drive. Make sure that device is jumpered as master and very carefully plug in the data cable to the device with the BLUE end connected to the motherboard. it detects the SATA, detects the IDE primary, but never it detects the slave dvd writer.

Bios Doesn't Detect Ide Hard Drive

See More: Install IDE Hard Drive | Install SCSI Hard Drive Related Articles - ALSO ON EaseUS SOFTWARE EXT Data Recvoery. 2016-08-03 17:19:21 Daisy - Free EXT File System Data Recovery Most likely you set your jumper wrong. Detecting Ide Drives Problem Sometimes, but rarely, a hard drive or CD Drive IDE can be bad... How To Connect Ide Hard Drive To Motherboard Troubleshooting No hard drives show up: Do you have two drives on the cable?

Join the community here, it only takes a minute. To find out more and change your cookie settings, please view our cookie policy. Did you jumper something wrong (ie; master/slave)? IDE ribbon cable connectors each have one hole blocked off so that they only plug into the ports one way.If everything is set this way, the mobo should detect the optical Hard Disk Not Detected In Bios Laptop

IDE drive plugged into the secondary.. This allows the cable to select if the drive is master or slave based on the position on the cable. See more IDE cabel hard not detect Pc not detecting ide drives Ide cable : not dedected Hard Drive detected,but not accessible (Solved) No hard drive detected [Solved] (Solved) Error message: i have my own gfx card and such Aug 2, 2010 #13 zoeleonard20 TS Rookie Unplug your cd rom see if it detects your hdd then unplug your hdd see

Privacy Policy | License | Terms & Conditions | Uninstall | Resource | Data Recovery Solution | iPhone Recovery | Android Recovery Discussion Boards Open Menu Discussion Boards Open Menu Welcome Don't force the plugs. I can only see a listing for a single hard drive in this model.Thanks!

They had to be called something.

However, since you installed extra RAM, the system behaves differently. If your using Windows 9x (why?) then you'll want to check out bootdisk.com and find something that'll cover your needs. To get around this you'll want to use that install disk that came with the hard drive or if you're a relatively advanced user a BIOS update should be available. This is NOT common, but a few early BIOS's had odd restrictions.

Otherwise, check and consider changing every single entry... Discussion is locked Flag Permalink You are posting a reply to: Problem IDE hard drives, not detected in bios The posting of advertisements, profanity, or personal attacks is prohibited. I want to know if it fails after a short time, a possible bad hard drive. http://magicnewspaper.com/hard-disk/disk-working-hard.html If this new drive is going to be your main drive then use the partition application that is built into Windows.

I have also checked the properties of the IDE drive by right clicking and checking the properties. you likely have some problems that can be corrected with changes as you boot to or Start with Default, then go through each setting on the list. hope you would've experienced such a disaster before I'm also experiencing the similar problem with my SATA 250GB HDD, 80GB IDE HDD and the dvd writer after I upgraded my memory If your computer can't "see" the device, you can't use it.

Or, sometimes they can all be set to cable select, depending on the cable you're using. Then, plug in the power cable to it.