Home > Hard Drive > 2nd Drive On Ide Problem

2nd Drive On Ide Problem

Contents

The last option is the normal way. But it only recognizes a floppy as the source for the SATA controller. Saved me a lot of messing around. So I asked could you save my lost data and I will spend more money with you and he said no? http://magicnewspaper.com/hard-drive/enterprise-hard-drive-as-an-extra-external-drive-any-problem-with-this-idea.html

You can connect either one or two IDE drives to an IDE ribbon cable. Basically, you’re looking for something that mentions CS or Cable Select, as well as Master, and Slave. Is there any indication that the BIOS has some overlap of ports, and you need to connect the second SATA drive to a specific port to avoid conflict with IDE devices? after adding the empty new drive to the pc and starting it up, it only finds the new 1 and the old 1 with windows 7 on it is just gone

How To Connect Ide Hard Drive To Sata Motherboard

Reply Rivers says: August 4, 2007 at 2:07 am I installed a extra hard drive in my pc and would like to completely wipe all data from it. Related Posts:What to consider when buying a new hard driveThree ways to keep your hard drive healthy and prolong its…LaCie 4TB Porsche Design USB 3.0 External Hard Drive ReviewWhat to keep Show more Loading... You should be able to remove a jumper with your finger nails, if not then use a pair of very small needle nose pliers and don’t bend the pins.

FIxed in a flash Report anal- May 3, 2011 at 07:43 AM its very useful for me , pls keep this type suggetion. Make sense? Previous PostHow To Install A New Hard Drive To Replace An Old OneNext Post3 DIY Computer Repairs You Can Easily Do Yourself 10 comments Write a Comment Chris Balfoort August 31, How Many Hard Drives Can Be Connected To A Single Ide Cable Do I just set the new drive as slave until I load the image to it and then powerdown and remove the old drive and set the new one to master?

It sees any other IDE drive attached, but not the HDD. Ide Hard Drive Jumper Settings Thank you so much for this information… I was going in to my computer and to no avail didnt see the second hard drive. As long as your motherboard has both SATA and IDE connections available and you set the switches on the drive appropriately, it should work! https://www.cnet.com/forums/discussions/mixing-sata-and-ide-drives-in-a-system-115142/ Same goes for SATA controllers.I think some SATA drives have legacy IDE plugs on them, but I'd only use the SATA plug with the small serial cable.

If you find out any good info, please let me know...thanx!Regards,Robert Flag Permalink This was helpful (0) Collapse - Sata is primary by edersch / July 28, 2005 9:26 AM PDT How To Install Ide Hard Drive I presume that this is due to XP If it is, MS deserve a k*ck up the backside!!! Are you looking for the solution to your computer problem? I've saved this to my useful websites list for easy reference!

Ide Hard Drive Jumper Settings

First step might be to try to return to the last configuration that worked. http://www.techspot.com/community/topics/cant-detect-hard-drive-after-adding-a-second-one.152654/ It is up and running but now my computer does not recognize my second drive. How To Connect Ide Hard Drive To Sata Motherboard Look at the back of it, where the ribbon cable and power cable are, there should be a white or black jumper on a couple of pins. Sata And Ide Hard Drives Together So you could take an old 386 drive from 1988 and plop it into your Pentium 4 from 2005, and it would work!

Because of just that, they are NEWBIES. useful reference I am trying to replace my current hard drive and install WindowsXP on it. Thanks for the instructions! egleyesJan 14, 2011, 10:45 AM Yes i have checked that cables are firmly attached, i also tried different jumper settings. How To Connect Ide Hard Drive To Motherboard

My HD crashed so I purchased a new SATA drive. Choose your language. This should at least get you started. my review here Another alternative is to buy an adapter card that plugs into the motherboard and has the sockets you need.

Loading... Seagate Ide Hard Drive Jumper Settings The physical installation is actually pretty easy. Further to my post above...My only guess is the IDE-to-SATA adapters attached to the IDE hard drives are junk.

If so, hunt for a free Molex-style lead.

Following your instructions, I have now successfully added a Samsung hard drive and Windows XP has recognised the primary slave. Once it loads, you should see an "Initialize Disk" wizard pop up. Next, try this (on the basis that the optical unit is working OK). Western Digital Ide Hard Drive Jumper Settings Finding the manager and getting it to format so I could see it on my computer was the missing step.

I will replace BOTH ide cables and do the master slave thing once again. So when I get to the prompt that ask to insert a disk in A:/ the only option I have is to insert the CD… I've tried to set my BIOS Just rock it back and forth (lengthwise along the narrow side of the drive), taking care not to rip the connector off the drive. http://magicnewspaper.com/hard-drive/drive-image-copy-drive-problem.html I have an 80gb IDE and want to add more memory.

Style Default Style Contact Us Help Home Top RSS Terms and Rules Copyright © TechGuy, Inc. Helpful +1 Report tjmartineau 38Posts Friday September 19, 2008Registration date December 23, 2008 Last seen Sep 27, 2008 at 04:54 PM Do you have an IDE CDrom or DVDrom drive? Aug 31, 2010 #1 Leeky TS Evangelist Posts: 3,797 +116 Connect the two hard drives SATA and power connectors... Computer systems are still way too complicated for the average user!

If the optical drive is the only item attached to the IDE ribbon cable, then it MUST be the Master device on that port. Ready to use, my system boot by HD SATA and use HD IDE as swap and backup drives.It's all.[]sClaudioPS: sorry because my english is short compreensive (= poor) but i try After boot windows xp/operating system on HD SATA, i re-activate IDE HDs and after backup data, repartitioned like i want. 5. It may have its own BIOS to check.

colinsp replied Feb 1, 2017 at 1:40 AM ***COMPUTER HAS BEEN BLOCKED*** wannabeageek replied Feb 1, 2017 at 1:00 AM Huge font and scroll bar problem davehc replied Feb 1, 2017 IDE ribbon cable connectors each have one hole blocked off so that they only plug into the ports one way.If everything is set this way, the mobo should detect the optical one of the 20 GB is Primary and the other two are slaves. What are these cables called so I can purchase one?

the surprising thing is that, it was working all these years until I touched it for RAM upgrade. F1 to retry boot. successfully installed second hard drive thanks to this post 🙂 Reply Joe says: August 23, 2009 at 11:14 am I have a 320 gig IDE hard drive .Im trying to install All rights reserved unused

Space to attach dongle. Note that some older PCs use 40-conductor IDE cables, not the 80-conductor ones current drives require. (Compare your kit cable to the one installed—the 80-conductor variety has much thinner wires.) 80-conductor First, the data connection. My hard drive crashed, but I had a back up one.

Some SATA drives do have a jumper which controls the speed of the SATA drive itself, but you do not need to worry about anything related to master, slave or cable