Home > Hard Drive > 750GB ATA Hard Drive Problem - Not Showing Up After Format!

750GB ATA Hard Drive Problem - Not Showing Up After Format!

Contents

They might be wrong or dangerous. If I try to create a new partition, it says no partition table found. I currently have an external drive connected which I use as a network drive. You can try posting the problem in the ‘internal hardware' subforum at bleepingcomputer.com I do many repairs there and either myself or someone else would probably be able to help you. http://magicnewspaper.com/hard-drive/wd-750gb-external-hard-drive.html

Same thing here, I can't see the drive in the utility tray, i put it in my other older (2008) macbook 15 it worked and I formated it in 1 minute. And also because the hard drive is still power on, I'm hearing it. Helpful +2 Report chrsjenko Aug 3, 2009 at 03:43 AM Januz I also tried to put drive into an external drive enclosure as well as several different machines, changing bios settings Got a new cable - same problem. http://www.tomshardware.com/forum/267218-32-hard-drive-showing-format

2nd Hard Drive Not Showing Up Windows 10

You may need to run the dos command using administration level mountvol /e Sometimes windows will have got set to NOT look at the partitions on a drive - the symptom When your tractor breaks or your cell phone stops working, they want to be the only people who can fix it. Selected that I wished to format the disc and then left it running - 12 hrs later and it was still running with no movement on the progress bar.

If the drive is formatted and working properly, you'll be presented with the Windows Auto Play dialog. I am afraid that my files are lost. I tried this and am back in business! Hard Drive Not Showing Up In Disk Management Windows 10 I'm affraid it comes from the logic board, since I don't understand how a cable could suddently stop working.

Just disconnected my Toshiba HDD 350 GB while working, after that I've tried to reconnect it again but here is the results: 1- at the first try my laptop is not Hard Drive Not Showing Up In Disk Management My external disk drive is 500GB Seagate Free Agent Go Flex Drive. Run windows 7 x64 install disk (with the 3tb drive being a secondary drive another hard drive had windows 7 x64 already installed) and format both parts of the 3tb but http://knowledge.seagate.com/articles/en_US/FAQ/006183en Here is an post about reading the results… http://html5.litten.com/accessing-and-assessing-a-hard-drives-s-m-a-r-t-data/ James Heinz • February 15th, 2013 at 1:30 pm Hi James!

B Was this answer helpful? Mbr Or Gpt For Hdd Thank you so much! It doesn't boot in single user, verbose, or safe mode. The pictures of the repair process below are from the actual repair of this drive.

Hard Drive Not Showing Up In Disk Management

Bernie Thompson January 5, 2013 Reply Hi Hongtao - Yes, Windows 8 has been relatively problem free. http://blog.atola.com/restoring-factory-hard-drive-capacity/ Have you tried looking at the drive with TestDisk yet? 2nd Hard Drive Not Showing Up Windows 10 Rick December 14, 2015 Reply Hi just purchased one of these and connected a western digital but can not seem to access the files that are on the hard drive already, External Hard Drive Not Showing In My Computer James Steph • March 25th, 2013 at 6:27 am Sorry, I meant TestDisk instead of CheckDisk.

Good luck, hope this helps. Get More Info Yes No Voted Undo Score 0 Cancel Comments: Yes please, I'm having this problem... My hat is off to you...thank you, Thank you, THANK YOU! 06/14/2015 by Jay Ell This worked great! Seagate uses the SeaTools diagnostic software to test the SMART status of the drive. Internal Hard Drive Not Showing Up

That is, nothing happens when I right click the mouse. Windows XP Windows 7 DO NOT FORMAT THE DRIVE When attempting to access the drive in Windows you may see a message asking you to format the drive DO NOT FORMAT Contact [email protected] if you're still having any trouble. useful reference Backup.log will contain a copy of the partition table prior to any changes. (mount a drive and copy backup.log to that when you are done if you are doing this in

If you are short on time, attempt a timed zero-fill of at least a few minutes. Hard Drive Not Showing Up In Bios That's about all I can do here. Windows assigns a number to all hard disks, solid state disks, USB drives, and card readers, so don't be surprised if you have to scroll down a bit-in our case the

The partition (there was only one on the disk) shows up with the correct name, yet there seems to be another problem.

may this one have the same firmware problem? Try Disk Health. 3. Dock powers up. Hard Drive Not Showing Up Windows 7 I tried to connect another hard disk and got the same error message.

I'm going to make use the backup.log, write a new partition table and then see what happens. Sorry for the confusion. your post http://www.bleepingcomputer.com/forums/topic481048.html came helpful for me.. this page now how to proceed.

putting the tape: instruments: masking tape(blue or white), a small flat screw driver, and scissors. This can take many hours depending on many factors including the drive capacity, so leave adequate time for this. If I try to create a new partition table, it shows a "Input/output error during write on /dev/sdb" error after several minutes. Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz?

Then hit Q until you are out of TestDisk. I want to know if i can recover data from it and what my options are ? The reason for this is often because of the way these drives are designed to be accessible by computers that normally can not access drives larger than 2.2TB. So you can fix the stuff you own quickly—and get back on with your life.

Could be that TestDisk doesn't work with 3TB hard drives? https://www.youtube.com/watch?v=Amg5w0rl... To upgrade to a new drive, copying your data from the old drive to a new one, see Document ID: 201991. If you get another drive or free space on another drive or flash drive that you want to copy some or all of the data to, let me know if you

The usb has only 1 file on it when I tried to use the usb at home. I've seen this happen before and we'll want to check whether files are not in hidden mode.Click on "Start" -> In search box, type cmd and press "Enter".A Command Prompt window Joshua Henry June 22, 2015 Reply Sorry to hear you're having troubles seeing the data. As soon as I connect them internally, I get a flashing question mark folder.

Ritchie Blogfried Pettauer • March 23rd, 2013 at 10:39 pm Hi James, first of all: thank you for this excellent guide! Please help me here.