Home > Hard Drive > .a Few Days After Install Of Maxtor Ultra SATA 160GB Hard Drive.

.a Few Days After Install Of Maxtor Ultra SATA 160GB Hard Drive.

Contents

after reboot the system was VERY SLOW to boot and run programs, and i noticed a clicking sound from the new drive. I've hooked up all the cables and turned the drive to "On" in the Setup Utility. Reply Robert says: October 25, 2008 at 3:50 pm Great Article. The physical installation is actually pretty easy. Check This Out

On a SATA hard drive, position of the drives on the cable does not matter at all because a SATA cable only accomodates one drive. For a couple of reasons, I have decided to mount the drive inside my PC. Dyan Reply Dyan says: December 29, 2007 at 11:32 am Joshcore, can you reply me. Using cable select worked out great.

Maxtor Hard Drive Jumper Settings

Thanks for the help. It does not recognise the difference in size. Good job A+ on te article Reply RepairGal says: January 8, 2009 at 9:42 pm Anyone who doesn't understand what a "jumper" is shouldn't be trying to change out their hard

Plug the system in and turn it on. This will prevent frustrations about losing programs after you have already formatted your computer. Most motherboards have two IDE channel connectors. Maxtor N256 Specs software showed that basic drive test FAILED even though data "Seemed OK".

Reply Fred says: August 16, 2009 at 2:08 pm Thanks to your excellent instructions I was able to install a new hard drive with only minor pain. Maxtor Diamondmax Plus 9 80gb It may cost a bit more, but at least you'll know you're getting what you need.Other than that....the drives work great. Much needed. http://newwikipost.org/topic/lpc2ElUc1qkIgAcATq8wnrQOrqm8YcSz/Hard-Drive-for-HP-ultra-slim-7800.html List unavailable.

If you are replacing your old hard drive, remove the cables from the old drive. Maxtor Diamondmax Plus 9 Jumper Settings How do I get my computer to recognize it. But having read this article in advance, I felt confident I could have overcome installation issues. Cher Reply Kieron says: August 22, 2007 at 11:25 am How do I set up a slave hard drive in windows without formatting it as I have information on it.

Maxtor Diamondmax Plus 9 80gb

There are no jumpers to worry about on SATA drives. https://www.amazon.com/Seagate-L01V200-Maxtor-Ultra-Internal/dp/B000IHXDR2 The drive is a SCSI. Maxtor Hard Drive Jumper Settings Thanks a lot! Maxtor Sata Hard Drive Jumper Settings Can u please guide me/help me to install the new system.

The unit runs at 7200 RPM (vs. 5400 RPM for lower priced or older hard drives) and features a massive 16 MB buffer rather than the 2 MB or 8 MB his comment is here If you need a separate controller card, install it now into any unused motherboard slot. one of the 20 GB is Primary and the other two are slaves. Booting from the old drive allows recognition of the new drive no problem, just can't boot from the new one. Once Installed What Needs To Be Done To The Drive And What Do These Two Tasks Do

Ask a Question See Latest Posts TechSpot Forums are dedicated to computer enthusiasts and power users. You might download the drive diagnostics from Maxtor's website, if you didn't get a floppy or cdrom with the drive. The advantages of Serial ATA are numerous, including faster performance, decreased power drain, and less cumbersome connector cables. this contact form The primary drive on a channel is called the Master, and the secondary one is called the Slave.

thanks guys for creating this it sure is a help for newbies out there 🙂 as Kyle said waaaaaay back, "I did'nt know that disk management exist" hehehe Reply Bill R Maxtor N256 Jumper Settings All three settings blue screen on me. Was this review helpful to you?YesNoReport abuse2.0 out of 5 starsDisappointed CustomerByRonnieVon March 10, 2007I originally purchased two of these drives and installed them in an Intel matrix raid array (raid

If you are installing a 3.5″ drive into a 5.25″ drive bay, you may need to add rails or a mounting bracket to make it fit.

As painful as it is, it might be worthwhile to call the manufacturer and see if they have a solution, because it may be a common problem. Short URL to this thread: https://techguy.org/234464 Log in with Facebook Log in with Twitter Log in with Google Your name or email address: Do you already have an account? Reply B.Ranganathan says: February 27, 2009 at 8:09 pm Dear Sir, I am using windows xp 2003 operatin g system. There Are Two Tasks That Need To Be Done With A Hard Drive Before The Operating System Can Use It. This was more than Helpfull in my Latest Conquest!!!

I recommend this product to any user that wishes to upgrade their computers memory and speed.Read more0Comment|Was this review helpful to you?YesNoReport abuse5.0 out of 5 starshard diskByAlboheron February 6, 2009i Reply Darklance says: August 16, 2007 at 3:05 pm Thankyou for the info David.. it's as easy as using a memory stick. http://magicnewspaper.com/hard-drive/can-t-install-xp-sata-hard-drive.html Press or F4 to enter RAID utility 1 WDC WD10EADS-00L5B1 WDC being the new drive on Port 1 of the SATA controller of course.

he said I don't know but you fried your set like a blackman handling chicken in a kitchen! ?!?!? Great website!