Home > Help With > Help With DVD Player And SATA Card

Help With DVD Player And SATA Card

Contents

Thanks again Report • #5 Tubesandwires January 30, 2011 at 09:21:36 I am assuming that you HAVE loaded bios defaults in the bios after you flashed the bios - if you How was early randomness generated? The set of complements equal to the complement of set How can I black out a bright bedroom at night? SATA III drive, unless you paid a lot more for a particular drive size (there's not many of them yet) or you have a solid state hard drive. - it appears

But there are also transition motherboards that have SATA sockets and one or two PATA sockets. The Boot Drive should be in the lowest Number SATA Connector and the Optical Drive that you want/need to Boot from should be in the next highest Number. If that doesn't work, it would indicate lack of power. If you use something such as a cardboard tube with it touching the drive between the drive and your ear, you should be able to hear whether it's spinning or not. More Bonuses

Ahci Compatible Dvd Drive

An error (403 Forbidden) has occurred in response to this request. Didn't realise the damage you could do otherwise. It is the next in my series of articles on computer refurbishing.People have three basic questions about SATA and IDE disk drives: How can I connect my old IDE drive to Didn't realise the damage you could do otherwise.

This is just how the Hardware works. Not all the 4 hard drives need to be bootable. silverhalo replied Feb 10, 2017 at 12:15 PM Access - Building database to... Tough luck.

BTW, despite having read through http://en.wikipedia.org/wiki/Serial_ATA#Cables.2C_connectors.2C_and_ports I am fuzzy on the differences between connectors, cables and ports. Ahci Vs Ide The drives are two pairs of the same size, 2 x 500 Gb and 2 x 300 GB or something like that. no. http://www.tomshardware.com/answers/id-3038047/suggestions-sata-controller-card.html Here's how the IDE connector sockets on the motherboard look, along with the ribbon cable that goes from the motherboard socket into the back of any IDE drive: PATA Photos (Wikipedia

How can I best mix IDE and SATA drives in one system? Well you can be led up the garden path and what a path. I do understand the the different Sata connections (Sata 2 and 3)of this mboard.The Seagate HDD drive I have installed is (allegedly) a Sata 3 device (Seagate Barracuda XT 2Tb) but The introduction says: The Plop Boot Manager is a small program to boot different operating systems.

Ahci Vs Ide

If the mboard's bios Setup has the SATA controller(s) in SATA a.k.a. I have tried three different optical drives but they are not detected by SATA 2. Ahci Compatible Dvd Drive I bought a PCI Expres SATA controller as I needed more SATA ports. OSNews.com uses icons from the Tango Project and FamFamFam.

When i set the computer up after i built it also failed to see my ssd drive or another hard drive on the asmedia controllers too so had to swap them Two hard drives are connected: a 1 TB SATA disk and a legacy 160 Gig IDE drive connected with Syba. If your power supply does not have an 8 pin connector that fills the socket, or a matched pair of 4 pin connectors on the same wiring that plug into the Like PATA, the SATA specs have evolved quickly to improve data transfer.

Many products just cost a few dollars. The example I/O controller card below gives you one SATA socket, one PATA socket, and one eSATA (external SATA) socket. Hours/days of misery and wasted time.Now the warranty round-about starts.Thanks for all the good advice. On cheaper older power supplies, all the +5v wire (red) leads are sourced from the same place on the board inside the PS, all the +12v wire (yellow) leads are sourced

Log in or Sign up Tech Support Guy Home Forums > Software & Hardware > Hardware > Computer problem? It's extremely unlikely the mboard was intially defective - if it does prove to be defective, it's a lot more likely you damaged it (such as by you not disconnecting the Seems only SATAs 1-6 (sata 2s) show up as detected or not in this mboard."Yes, that appears to be right.I have an older Epox mboard that has an additional (older) Marvel

Each wire has a metal end with two tangs on it that lock it into the hole in the connector - rarely, there may be one or more wires that are

Advertisement osp001 Thread Starter Joined: Nov 9, 2004 Messages: 17 I have an HP Workstation XW6200, plenty of RAM, plenty of speed, etc., running XP Pro. Report • Start a discussion Ask Your QuestionEnter more details...Thousands of users waiting to help!Ask now Weekly Poll Have you used Facebook's "Safety Check" during an emergency? Computing.Net and Purch hereby disclaim all responsibility and liability for the content of Computing.Net and its accuracy. If you DO want to set up a RAID array, - you must set it up BEFORE you install an operating system. - you must install drivers - if you are

Computing.Net cannot verify the validity of the statements made on this site. See section 3.42 Storage Configuration for details. Couldnt see it anywhere on the system as a drive. Does it work correctly?Col 0Votes Share Flag Collapse - Reponse To Answer by patihk19 ยท 6 years ago In reply to What exactly do you mean ...