Home > How To > {SOLVED} Cd-rom Connections

{SOLVED} Cd-rom Connections

Contents

there is no honest way to explain it, because the only people who really know where it is are the ones who have gone over. -- Hunter S. Glad we could help. :) Reports: · Posted 4 years ago Top Topic Closed This topic has been closed to new replies. Using a text editor, add the drive letters of your hard disk partitions after the SMARTDRV statement in the AUTOEXEC.BAT file (for example, SMARTDRV C D). I'll try to explain again, You have two options: 1. http://magicnewspaper.com/how-to/solved-new-wireless-connections.html

If it is not, you must update your AUTOEXEC.BAT file manually. This is because the AUX AUDIO port is: left-ground-ground-right How to fix: Pull out the white wire from the connector end of the cable and move it to the empty slot There are two ways to prevent the USB from using IRQ 15: - Attach a device to the secondary IDE controller. - Make IRQ 15 unavailable in the Configuration/Setup Utility program. So don't splice those audio signal wires directly together.

How To Connect Dvd Drive To Motherboard Sata

Using the IDE data cable provided with the IDE CD-ROM drive, connect the CD-ROM drive to the primary IDE controller as a master device. Gechlik here from AskTheAdmin.com doing a weekly guest blogging spot for our new found friends at MakeUseOf.com. You have to be very careful when doing the tests to determine pinout of soundcard you don't know, because all tests must be performed when computer case is open, soundcard is

It is 4 pin connector with 4 wire plus 2 wire wind together... I know i have some limitation in using it ...but still trying to see if i can work with it.. Does it exist? How To Connect Ide Dvd Drive To Sata Motherboard Or the CD-ROM and sound card were purchased separately and the CD-ROM grey audio cable was the wrong type for the combination of card and CD-ROM.

if you cant just buy a new optical drive they cost as low as 10$ smorizioAug 22, 2015, 9:27 AM http://www.satacables.com/assets/images/IMG_841223.jpghttp://f.tqn.com/y/pcsupport/1/W/5/7/-/-/sata-power-cable.jpgin the new mb box should be one or two sata How To Repair Cd Drive In Laptop Your sound effects work fine (because they went through the ISA bus) but CD audio playback only cames out one channel. Typically, internal CD/DVD drives are spec'd for power requirements in the +5V @ 1.5A, +12V @ 1.5A, range, so if you attempting to power your CD/DVD drive with a el cheapo view publisher site there is no honest way to explain it, because the only people who really know where it is are the ones who have gone over. -- Hunter S.

Because of the simplicity of the mixer circuit the signal level is reduced but it otherwise works nicely. How To Repair Dvd Writer Lens or one must be with 12V and other with 5V ? You cn wire an audio cable from CD-ROM headphone output to line level inout of the soundcard. If you only have two wires from the adapter you MUST wire them to a 12V regulator and a 5V regulator to get the voltages the drive needs.

How To Repair Cd Drive In Laptop

I tried connecting the 12V and 5V adapter to the power source....but nothing happens.... http://www.edaboard.com/thread340536.html How to get to know CD-ROM audio output pinout Typically CD-ROM manufacturers print out the pinout to CD-ROM itself or to the manual. How To Connect Dvd Drive To Motherboard Sata How do I install Windows(8/7 - 64bit) without a CD/DVD ROM? How To Repair Dvd Drive Not Reading II.

new PC...which CD/DVD ROM DRIVE????? my review here Maybe it will stop the questions – but I doubt it! The black wires are both ground and internally joined in the drive. Helpful Notes: 1.Operating-System-Specific Notes Windows 3.x If the IDE CD-ROM drive is attached to the primary IDE controller, problems might occur when Windows 3.x operates in Enhanced mode. How To Repair Dvd Writer In Pc

Originally Posted by bigdogguru I'm not sure what the issue is here, as it is quite straight forward. If you only hear the sound from left or right channel then remove the wire which goes to soundcard and test if the CD-ROM work as it should without it (wrongly Full systems and upgrade kits are not required to observe the following specification: A Multimedia PC CD-ROM drive component must include a cable to connect the drive's analog audio output connectorto click site Replace the computer cover.

direct 19V is advisable ? Dvd Player Problems Look for the following statements: [386Enh] ...VirtualHDirq=off This statement is required only if the CD-ROM drive is a master on the primary IDE controller. The diagnostic program is self-documented and can be run only from DOS (not virtual DOS on OS/2 or DOS under Microsoft Windows).

The correct way to do the connection is to use an audio mixer circuit.

Teardown Videos Datasheets Advanced Search Forum Analog Design Power Electronics [SOLVED] [moved] How to Connect CD ROM Drive with Adapter externally ! + Post New Thread Page 1 of 2 solved can't connect DVD drive to psu solved Will a SATA I (1.5) dvd rom slow my sata III (6GBs) hard drive to 1.5? Other possibility is that if you know the pinout of the CD-ROM audio output, you can wire the audio signals from it to separate audio connector on the back of your How To Fix Dvd Drive Not Detected Use one of the following procedures to connect the cable and set the jumper in your CD-ROM drive, depending on the current configuration of IDE devices in your computer: - There

Reason: Image converted from external server to Edaboard attachment 5th July 2015,21:13 #6 SunnySkyguy Advanced Member level 5 Achievements: Join Date Sep 2007 Location Richmond Hill, ON, Canada Posts 6,527 Helped But the moment I place a DVD movie in it will not read the disc. It could be a Windows operating system problem that is preventing your drive from showing up or reading disks and finally it could be that disk is garbage. navigate to this website to fix this you have to change some registry settings - it's easy enough (just download a tiny file and run it) but if you don't know about it you'll be

Connect the +12V supply output to the +12V input on the drive and the 0v from the 12V supply to the other ground on the drive. Ok solved for which pin is 12V A good design question lists your overall requirements™ The best question deserves a better answer. ™ ... However, the USB is a Plug and Play device, and it takes IRQ 15.