Home > How To > {SOLVED}Slave Drive Configuration

{SOLVED}Slave Drive Configuration

Contents

can i still format the new drive and then install my photo editing tools on it , without any problems? By continuing to use our site, you agree to our cookie policy. At boot, you usually press DEL or F1 to eneter setup. Advertisements do not imply our endorsement of that product or service. http://magicnewspaper.com/how-to/solved-how-to-format-slave-drive.html

When installing Windows 2000 to a Serial ATA drive, you may need to specify the SATA controller drivers early on during the installation. This may still occur even if you are installing a single drive. If the hard drive is still OK then it should show up fine. During the installation process, you will be given the option to create partitions.

What Is A Slave Hard Drive

a7n8x Deluxe - Optical Drives Master/Slave Problem Master/Slave Hard drives master/slave for drives??? Saved me a lot of ‘messing about' time. This will prevent vibration and provide additional electrical grounding. Go through the appropriate prompts, making sure to select your older drive as the source and your newer one as the destination (pay careful attention to the hard drive sizes indicated

i changed the primary drive in the bios to the ide hard drive , still couldnt get passed start up mode. The tip on setting the jumper properly is what got my drive up and running. Getting it ready for use takes a little longer. Master Slave Computer Setup If you're not already familiar with forums, watch our Welcome Guide to get started.

Left-click on Next to continue. How To Slave A Hard Drive Windows 7 xxx Reply walter says: August 17, 2007 at 12:47 am Hello, I've been tring to install a SATA hard drive with no luck. Note: When you see the message, No signature found on Disk 1, press YES. http://www.wikihow.com/Configure-Master-and-Slave-in-BIOS-for-Two-Hard-Drive-Disk-in-a-Single-System Copyright 1990-2003 Dell Computer Corp.

This full-featured backup/restore utility from a trusted company will help you clone your PC and restore it to your new hard drive. How To Set Up A Slave Drive far from a computer expert I was able to use your information to find the missing step I needed to install my sata 2nd drive. I am literate, but not geek (all the way) … I have a Dell GX 240 Tower with 1GB ram,and its a 1.2.GHZ pentium 4 system. Your website got me passed this and told me how to do it without that.

How To Slave A Hard Drive Windows 7

Reply Norm says: September 23, 2009 at 12:21 am Having the same problem. If you want multiple partitions on this hard drive see the additional instructions below: Adding Multiple Partitions to your Boot Drive durring a Windows 7 Installation: Important: Western Digital Technical Support What Is A Slave Hard Drive Please contact your system or RAID controller manufacturer for assistance on defining your drive in a RAID Array. Master And Slave Drive Explained On the next screen, select the drive you are upgrading/installing.

I had done everything i could think of. http://magicnewspaper.com/how-to/how-to-add-slave-drive-without-formatting.html Turn the system's power off Mount the drive in the system Desktop Drives: The drive can be mounted in a standard 3.5"device bay. Choose the restart option. thanks guys for creating this it sure is a help for newbies out there 🙂 as Kyle said waaaaaay back, "I did'nt know that disk management exist" hehehe Reply Bill R How To Slave A Hard Drive To Recover Data

But I cannot get my second Western Digitial EIDE Hard Drive recognized. The next screen shows the drive you have selected to write the signature to (if this is a new drive install only a signature will be written, making the drive a PLEASE?!? More about the author This makes no changes so can't hurt anything.

Leave your dvdrom drive out for the time being. How To Make A Slave Drive SATA interface cables have keyed connectors to prevent incorrect installation. The other method in use by OEM makers, is called Cable Select (CS).

It will show you all of your drives & sizes.

The Write Signature & Upgrade Wizard displays. Dyan Reply s says: January 2, 2008 at 2:17 pm I am installing a second hard drive (60 GB, to be used for data only) on my 2 year old computer. Right Click on Hardisk that doesn't show a partition and choose "Import Foreign Disks" 4). How To Partition A Hard Disk Helped me over that last hurdle in getting my new drive up and running.

Reply Dave says: November 24, 2008 at 1:34 pm Hi I bought this on Ebay, it works realy well, you can connect any hard drive to a usb socket. is there a place to download it or what should i do? If you are simply installing a secondary drive, boot into Windows. http://magicnewspaper.com/how-to/adding-a-slave-drive-mostly.html Serial ATA (SATA) I, II, and 6 Gb/s Hard Drive Jumper Settings for 3.5" drives: Important: Caviar Black drives that have a model number of WD1002FAEX-00Y9A0 use the SATA 3.0 Gb/s

I would like to add a 2nd SATA hard drive and was wondering if it can be connected in serial with the existing hard drive. Sorry for the dumb question but is there really such a thing anyway?? Read the partition posts, and figure I would need to "ghost" the OS, or would a clean install be better and ghost the rest of the programs? Now when running a Norton system check it gives me this message: Hard Drive Integrity Scan !

Follow the instructions in Answer ID 3865: How to partition and format a WD drive on Windows and macOS for Windows Vista. Reply mark says: October 15, 2008 at 7:00 am Hi Did you sort out this issue as I have the same issue? the c drive that im using now as like no memary some one told me to stick them in my d/cd or my e/dvd/cd drive to keep them out of my The Create Partition wizard is displayed.