Home > Power Supply > ATX Power Supply Fan Running With No Panel Connecters Attached.

ATX Power Supply Fan Running With No Panel Connecters Attached.

Contents

Power supply light does not turn on or power supply fan does not spin If you still have no power, perform the following steps until power is restored or it is Posted on September 09th 2016 | 10:13 am Reply B Bob Maxwell I cannot get my ATX supply to turn on. By that I mean, when I hit the power button on the front panel of my case, nothing on the inside of the case happens at all except I see one So to manually turn on an ATX power supply we only need to pull the PS_ON# pin to ground. why not try these out

Would it be unwise to purchase a beefier power supply and assume that it's that? The power supply is less than a month old, but it's just an Antec 500w power supply. Best answer SR-71 BlackbirdJun 18, 2013, 2:44 PM The majority of them are the samehttp://i1123.photobucket.com/albums/l546/area51reopened/fp_header_zps8a69fea1.jpg SR-71 BlackbirdJun 18, 2013, 2:44 PM Thanks for posting in the forum we appreciate it. All Rights Reserved. More Bonuses

How To Test Atx Power Supply Without Motherboard

We can not just simply plug the PSU into the mains supply and expect to get the required 5 or 12 volts output. Then they turn off and back on, no display solved Need help! There's this blue and black thin-wired three or four pin connector coming from out of the power supply, but it's attached to nothing (never has...leads me to believe maybe my power

Have the computer serviced, or remove the components and replace them, one at a time, to find and replace the defective component. Problem is, if you attach a ATX power supply to the mains it will simply do nothing. The power supply cord is basically bullet-proof, unless you cut through it with something, but if the PC gets moved or the cord gets kicked, it's easy for that cord to Atx Power Supply Pinout Turn On conerning the additional feature using Lm317, 240 ohms resistor and capacitors to give a separate adjustable output voltage from 2 to 12volts, can you pls give detailed connection layout or diagram?

If you are having trouble try that

Great tutorial by the way. Test Power Supply Paperclip If you believe the motherboard was badly damaged by a power surge or a short, it's possible the switch circuit has failed or that the power supply is immediately shutting off Finally I switched back in the 6600 which has been functioning with the PC for over a year, and the same exact problem persisted. http://marcomiltenburg.com/2011/09/18/how-to-test-an-atx-power-supply/ No resistors.

Also note that some power supplies will not spin up the cooling fan(s) unless the power supplies reaches a certain temperature. Turn On Power Supply Without Motherboard 24 Pin Firstly though, the ONLY thing I knowingly myself did different than all the unattaching and reattaching everything all night and morning was... 1. I'm certain the CPU-FAN power is attached. 2. Older power supplies shipped with a manual switch to select the correct voltage (110V/ 220V).

Test Power Supply Paperclip

This is important! http://www.fonerbooks.com/power.htm If the system powers up, replace all adapters except the last one removed before power came on. How To Test Atx Power Supply Without Motherboard I bought a gadget recently so i could turn a 3.5" sata hdd disk to usb disk. Atx Power Supply Jumper If you can't locate a failed component by visual inspection, you need to have access to a test-bed system (an inexpensive but completely functioning PC for testing questionable parts).

Take the side off the PC case and make sure there are no signs of life, that none of fans in the case are spinning, including the CPU fan, the video look at this site Show me how note: If you find the device that was causing the problem was a surge protector, resetting a breaker or fuse on the surge protector might fix the Case fans can also fail and make noise, as can the heat sink fans on the CPU, video adapter, or motherboard chipset. Sometimes they give the peak current requirement in Amps (A) at the supply voltage, usually 12V, so you multiply the two numbers for the power consumption in Watts. Atx Power Supply Turn On

Tried what I could from the stickies and other suggestions in posts that apply to me. Power supply fan is noisy or having interference Follow these steps to clean, and then test the fan. If that screw lands in just the wrong place, like an open bus slot, it could create a short and damage the motherboard. http://magicnewspaper.com/power-supply/power-supply-makes-clicking-noise-when-i-press-power-button.html Return to Diagnostic Chart One obvious reason the PC won't turn on when you press the switch is if the switch lead has separated from the motherboard.

Ich verstand, kein problem.

Quite simple ... A Connector On A Motherboard That Consists Of Pins That Stick Up From The Board This lead is usually labeled PW-ON or PW and it reaches from the front the PC case to a small block of metallic pins for case connections to the motherboard. If you're competent to work around live DC voltages in an open case, try to force the power supply on by shorting the green wire (pin 16, power_on) to any of

Unfortunately I didn't have a monitor or peripherals attached to it at the time so I didn't get to see any start up screens.

Since this connection is for information only, the fan doesn't draw power from the connector and it may only use one wire. Test for power. Follow it to the 20 or 24pin ATX plug. Atx Power Supply Turn On Without Motherboard The layout of the 24-pin connector is shown below.

Saved me a lot of investigation and worked like a charm. Start by removing the power and data cables from the DVD drive, you can do this with the power supply plugged in. Try the computer in a different outlet in order to eliminate the outlet as a possible source of the issue. http://magicnewspaper.com/power-supply/graphic-card-power-to-power-supply-or-connector-on-motherboard.html Any clues of what I may've done wrong is appreciated!

Because power isn't coming on at all with the motherboard attached, it's very unlikely that the problem is the power supply failing to produce all of the different voltages required by See how many you can define before you read the chapter. Figure 31: Making the 12 V power connection Finally, we need to do a "make up" connection, to compensate for the fact that we used a 20 wire instead of a Figure : Example of a power supply part listed on the HP Parts Ordering website If the part is available (has a green check mark), you can order from HP by

All of the high end video cards require more power than can be supplied through the PCI Express slot on the motherboard, so they are fed directly from the power supply Luckily, pin 15 - Black is next to it so I connected a switch between the Pwr_On signal (pin 14) and Ground (pin 15). Runs fine without the led. Unplug the power cord or switch off the power strip before removing each adapter, then reconnect to power up.

If the LED is still flashing (it should not flash with all connectors removed), plug the power cable into a different power outlet that is known to be good. To test if the power supply is working correctly you can measure the output voltage with a multimeter. An ATX power supply either has depending on the ATX version it support a 20-pins or 24-pins (ATX 2.0) connector. This page requires Javascript.

Typically there are two ways to find a file when you don't know what folder it is in. The +5VSB (+5 Volt Standby) always stays on even when the power supply is in standby. If the problem goes away when the component is removed, then please remove the recently added internal component. To me, incorrect grammar and spelling is mentally painful.