Home > Windows 2000 > Networking Cable Modem/NT And Windows 98

Networking Cable Modem/NT And Windows 98

Contents

You double-click Private Things from the root directory and get an Access Denied message, as you'd expect. Such connection is called : Direct Cable Connection ( DCC ) Like with any component on your system, you need hardware and software:Hardware : all these connectors on the back of For a solution to that problem, see the sidebar "Mapping a Network Drive." Inheritance and Permissions As we've mentioned, the most common mistake many people make in peer-to-peer networking is sharing This will allow the special applications to pass through the firewall function of the Wireless Cable/DSL Router. http://magicnewspaper.com/windows-2000/windows-2000-networking.html

In Windows NT: Click Windows Start, Settings, and then click Control Panel. To make a Win2K Pro computer a client, open the client's Network and Dial-Up Connections applet. If you click the check box to clear it, a Security dialog box pops up. If you cannot complete this ping, make sure all the cables are properly connected and that all the correct drivers are installed.

Windows 2000/nt/xp Configuration Options And Troubleshooting Pdf

If they do not automatically connect, rescan until they will detect it and connect. i can see the computer name a in computer a when i click the "computers near me" icon . To deny Everyone all access to Private Things, you open Private Things' Permissions dialog box and select Deny for Full Control, Change, and Read. That cabling should connect the PC and the Cisco Access Server (the Data Terminal Equipment [DTEs]) without the need for a null-modem cable.

I wondered if you had any insite on this issue? To avoid this mistake, you need to understand the rules of inheritance. Possible Solution: The default setting in Windows Me and XP is to not show all of the icons within the Control Panel. Windows 2000 Configuration Options And Troubleshooting Verify that the TCP/IP option is selected under Allowed Network Protocols.

To make an Ethernet connection: Connect one end of the supplied Ethernet cable to your PC's Ethernet adapter. If possible, reposition the Wireless Cable/DSL Router to reduce the effect of any of these obstacles. This technology lets you network computers by plugging them in to the same active phone line. Possible Solution: You need to verify the connection setting of your Web browser and that the HTTP Proxy feature of your Web browser is disabled.

Possible Solution: Make sure the power cord and all the Ethernet cables are connected correctly. Connectivity Troubleshooting Some applications can't use Uniform Naming Convention (UNC) share names to store and access files on remote computers. To ensure that you don't make that mistake, you must understand permissions and inheritance, which we explain in detail later. Monday - Friday Hungary --- [email protected] 8:00 A.M. - 6:00 P.M.

Windows 2000/nt/xp Configuration Options And Troubleshooting Interview Questions In Ibm

Under Win2K Pro's default inheritance, these two ghosts behave quite differently. Click Have Disk. Windows 2000/nt/xp Configuration Options And Troubleshooting Pdf Use the new connection, as follows: From the Start menu, choose Programs > Accessories > Communication > Dial-up Networking. Understanding Of Operating Systems Windows 2000/nt/xp Locate the Ethernet cable from your Cable modem that is connected to your PC’s Ethernet adapter.

If you are still experiencing any difficulties, proceed to the “Troubleshooting” section of this Guide. If you change a user's password, you must change it on each computer. You have two ways to let users access another networked computer. Thanks... Windows 2000 Configuration

Have you ever tried to find information thru Windows help or at Microsoft? Windows 98 Dial-up Networking by a Null-Modem Cable Follow the steps below to configure Dial-up Networking. Good Luck! Connect the included power cord to the power jack on the Wireless Cable/DSL Router.

ip address 10.10.10.10 255.255.255.0 encapsulation ppp async mode interactive peer default ip address 10.10.10.11 no cdp enable ppp authentication chap ! Ibm Technical Support Interview Questions Disconnect that Ethernet cable from your PC’s Ethernet adapter and connect it to the WAN port on the rear of the Wireless Cable/DSL Router. http://www.speedguide.net/ jmatt, Jun 21, 2001 #3 This thread has been Locked and is not open to further replies.

Enter the username and password that is valid on the Access Server. (The PC serial port is directly connected to the Access Server by the null-modem cable.) The dial number (a

The tested working configuration, along with the debugs of the Access Server, are shown below: ! On the Properties window, you click the Permissions button to access the Permissions dialog box. A Word to the Wise: Security, Firewalls, and More If you use an always-on connection, such as DSL or a cable modem, we advise you to implement some sort of firewall Basic Troubleshooting Questions Asked In Interview You can verify the bindings (click on the '+' to expand the display), it should only show NetBEUI-protocol.

To make a computer a gateway, open the computer's Network and Dial-Up Connections applet and right-click the icon for the Internet connection that you want to share. I select Everyone and click Remove, as Screen 2 shows, then I click Add to bring up the Select Users, Computers, or Groups window. Congratulations! To install the mdmcisco.inf file, add a modem as follows: Choose Start > Control Panel > Printers and Other Hardware > Phone and Modem Options.

To reformat a drive, open the Control Panel Administrative Tools applet and double-click Computer Management. Connect to the Access Server by following these steps: Double-click the Null-Connection icon. The setup-steps are identical with the DCC connection with a Win9x system: - Definition of the "Direct Cable" modem - define one NT4-system as Host - define one NT4-system as Client If you open My Stuff, you'll see Private Things again.

Turn on your Cable or DSL modem. Click OK. So, the ghost of Private Things in the root shared directory follows the directions we gave Private Thingsā€”to deny access. If you are attempting to create a Wireless connection but cannot connect to the Wireless Cable/DSL Router, make sure each Wireless Card is set to Infrastructure mode.

You are connected: The DCC Client connection allows to "View the Host", but also the Network Neighborhood is operational (since we have a network board, real or emulation, installed in the Right-click the LAN connection, select Properties, and select the Enable on-demand dialing check box. If you're new to Tech Support Guy, we highly recommend that you visit our Guide for New Members. Click Protocols and click Add.

Plug the power cord into a standard power outlet.