Home > Windows 2000 > Screen Freezes Windows 2000

Screen Freezes Windows 2000

Contents

Your Computer May Pause with a Black Screen If You Press ESC During Startup Microsoft Knowledge Base Artilce Q311799 - If you press the ESC key while your computer is starting, Microsoft IntelliMouse Is Not Detected or Causes Hang in Windows 2000 Microsoft Knowledge Base Article: 226015 - If there is a Microsoft IntelliMouse connected to your computer, the IntelliMouse may not Whether I clicked yes or no had no effect. Are you looking for the solution to your computer problem?

by freeze i mean the following: screen locks, mouse and keyboard are unresponsive, sound will loop for a few seconds, then go quiet. It then starts these components possibly causing more draw on the power supply. Like I said I... You Cannot Start a Newly Promoted Domain Controller After You Remove Windows 2000 SP2 SRP1 Microsoft Knowledge Base Article: 319783 - If you install Windows 2000 Service Pack 2 (SP2) Security his explanation

Windows 2000 Hangs On Startup

How to Troubleshoot Event ID 2021 and Event ID 2022 Microsoft Knowledge Base Article: 317249 - The server computer briefly may stop responding (hang) and one or more of the following Boot off of the newly created CD and run the short and long tests on the HDD. hussar, #4 2005/12/05 sparrow Inactive Joined: 2004/03/21 Messages: 2,282 Likes Received: 0 Trophy Points: 356 Location: minneapolis Computer Experience: Experienced XP has msconfig.exe. This behavior may occur more frequently depending on the computer's processor, memory, and graphics configuration.

Is there some way to find out what it's hanging on so I can try to just replace that file/reg entry? Your computer may appear to stop responding (hang) while the "Starting Windows 2000" message is displayed, and the status bar may pause between 50 and 70 percent. Burn the image to CD using IMGBurn also in my signature. Quick Links HelpWithWindows.com RoseCitySoftware.com Recommended Links Menu Log in or Sign up Search Search titles only Posted by Member: Separate names with a comma.

Almost always freezes during Windows 2000 "Starting up" process (blue progress bar about 2/3 complete). 0Votes Share Flag Back to Hardware Forum 3 total posts (Page 1 of 1)   Search How To Repair Windows 2000 Using Recovery Console There is some minor HD activity with maybe 3 or 4 blips. Maybe if I give an example of what mup.sys does it will become more clear. I installed the applicable security and system updates from windowsupdate.microsoft.com immediately after getting online, and the machine says it is running Win2k Build 2195, Support Pack 4Free.

My router crashed, and getting it back up took top priority. The server may recover on its own or you may have to restart it. Computer May Stop Responding with Object Auditing Enabled Microsoft Knowledge Base Article: 263627 - When object auditing is enabled, your Microsoft Windows 2000-based computer may stop responding (hang). put in new hard drive still did not work.

How To Repair Windows 2000 Using Recovery Console

Windows 2000 Shutdown Process Stops and Error Message Refers to Devldr Program Microsoft Knowledge Base Article: 296838 - When you attempt to shut down your computer and then restart it, an I thought I would be able to boot into safe mode, but today that didn't work either. Windows 2000 Hangs On Startup And leave the cover off.Bob Flag Permalink This was helpful (0) Collapse - hey, thanks by A Zen-like Chill / December 18, 2004 11:59 AM PST In reply to: Power, BIOS, Repair Windows 2000 Without Cd All submitted content is subject to our Terms of Use.

This shows as a hang at mup.sys because after mup.sys loads, Windows then goes into a more complicated portion of its boot process and this is where the actual hang occurs. Ken kjfrey55, Jun 8, 2005 #1 Sponsor bradly Joined: Feb 10, 2005 Messages: 773 I wouldn't try a repair install just yet... I was able to get the server to boot up under Safe Mode, but every time I've tried to boot it up normally it gets stuck at the same spot. the pc is about to get tossed out the window.

If you're not already familiar with forums, watch our Welcome Guide to get started. Boot Menu Is Not Displayed and Timeout Value Is Not Used Microsoft Knowledge Base Article: 242443 - If you install Windows 2000 on a computer with no other operating system installed, To troubleshoot this, see here: http://techtalk.yourtechonline.com/forum_startups.php However, after the initial "unchecking all", try and boot in regular mode, then follow the rest of the advice. section below.

Newer Than: Search this thread only Search this forum only Display results as threads Useful Searches Recent Posts More... Did the Fast repair, copied the reg files and then successfully rebooted. All rights reserved.

Tried booting to Last Known Good Config -Unfortunately, did this after logging on in Safe Mode so it probably wiped out the LKGC prior to the initial freeze 4.

Active Directory MMC Tools Are Slow to Initialize Microsoft Knowledge Base Article 270915 - Active Directory Microsoft Management Console (MMC) utilities may be slow to initialize and run. Boot to safe mode, remove all network components from your network config like TCP/IP, network client, NIC, etc. When the computer starts, you may see Event ID 7001. No, that one program doesn't work in Virtual PC 7 on the Mac or in VMware on Linux).

Still as clear as mud? When you click End Now, the shutdown process may stop and the computer may stop responding. Windows 2000 May Hang with USB Devices on Older Via Chip Set Microsoft Knowledge Base Article: 246755 - When you are using certain Universal Serial Bus (USB) devices on a motherboard http://magicnewspaper.com/windows-2000/windows-2000-freezes-while-trying-to-install.html Computer Hangs If USB Composite Device Is Removed While Being Reset Microsoft Knowledge Base Article: 278489 - Your computer may stop responding (hang) after you remove a Universal Serial Bus (USB)

please be specific. Happend to have some registry files in my c:\winnt\repair\regback folder - copied these into my c:\winnt\system32\config (after renaming existing ones)... ...and the system booted! Known Bugs and Issues... WindowsBBS.com is completely free, paid for by advertisers and donations.

An error (403 Forbidden) has occurred in response to this request. Startup Scripts May Appear to Hang Windows 2000 Microsoft Knowledge Base Article: 256320 - Your Windows 2000-based computer may appear to stop responding (hang) if the computer has a local policy Usually the mouse laser cycles at this point but goes out. At least to my untrained eye. (Great log format, with no timestamps and no verbose information...) I also tried enabling VerboseStatus, but that didn't seem to do anything at all. (I

When this is selected in combination with Use Printer Offline, the computer is put into a state where printing cannot take place, because the operating system cannot spool and store the by R. If you found this article on mup.sys hangs useful (or not) and have comments, criticisms, or suggestions please feel free to drop us a note using our Contact form Maybe consider Mup.sys acts like a router that calls the correct networking method to provide communication to that particular type of resource.

Also, the central processor unit (CPU) may appear in Task Manager to be running at 100 percent, even if there... I tried to reboot with CTL+ALT+DEL, but the system did not respond to keyboard input. Yes, my password is: Forgot your password?